# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug:0=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

#hdmi_force_hotplug:0=1
#hdmi_group:0=1
#hdmi_mode:0=1

#hdmi_force_hotplug:0=1
#hdmi_ignore_edid:0=0xa5000080
#hdmi_ignore_cec_init=1
#hdmi_ignore_cec=1
#hdmi_group:0=1
#hdmi_mode:0=1

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
hdmi_group=2
hdmi_mode=87
hdmi_cvt=1024 600 60 3 0 0 0

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
arm_freq=1800
gpu_freq=600

# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
#dtparam=i2c_vc=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
#dtparam=audio=on
dtoverlay=audioinjector-isolated-soundcard

# Automatically load overlays for detected cameras
#camera_auto_detect=1

# Automatically load overlays for detected DSI displays
display_auto_detect=1

# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2

# Run in 64-bit mode
arm_64bit=1

# Disable compensation for displays with overscan
disable_overscan=1

[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
#otg_mode=1
dtoverlay=dwc2,dr_mode=peripheral
# this driver is borked.. do fan speed manually
#dtoverlay=i2c-fan,emc2301,i2c_csi_dsi,midtemp=40000,maxtemp=60000
# Run as fast as firmware / board allows
arm_boost=1

# display
dtoverlay=WS_xinchDSI_Screen,SCREEN_type=2,I2C_bus=1
dtoverlay=WS_xinchDSI_Touch,I2C_bus=1
[pi4]

[cm5]
dtoverlay=disable-sd
# cm5 fan settings
dtoverlay=pwm-gpio-fan
dtparam=fan_gpio=27
dtparam=fan_temp0=40000,fan_temp0_hyst=5000,fan_temp0_speed=70
dtparam=fan_temp1=50000,fan_temp1_hyst=5000,fan_temp1_speed=120
dtparam=fan_temp2=60000,fan_temp2_hyst=5000,fan_temp2_speed=150
dtparam=fan_temp3=75000,fan_temp3_hyst=5000,fan_temp3_speed=255
# usb c peripheral mode
dtoverlay=dwc2,dr_mode=peripheral
# display
dtoverlay=vc4-kms-v3d
dtoverlay=vc4-kms-dsi-waveshare-panel,7_0_inchC,i2c1
# pcie
dtparam=pciex1_gen=3

#kernel=kernel8
initramfs initramfs_2712 followkernel

[all]
enable_uart=1
dtoverlay=disable-bt
dtoverlay=disable-wifi
ignore_lcd=1
dtparam=i2c_vc=on
#dtparam=i2c_arm=on

